---

About Product Features Product Testing Q&A Application Contact

PRODUCT (included in 1 kit)	Easy Green - 3 bottles @ 8 oz. each (green) NO-Slip - 2 gallons (clear) Grip Bond - 1 gallon (purple)
TIME NEEDED	1-2 hours for 1500 sq.ft. (includes cleaning floor) 2-3 hours for 2200+ sq.ft. (includes cleaning floor)
LABOR	2 crew (over 2200 sq.ft. use 3 crew)
EQUIPMENT	2-5 gallon mop buckets with squeeze attachments 3 long handled mops (with NEW DRY MOP HEADS) 1 deck brush 1 long handled squeegee (if available) 1 wrist watch

IMPORTANT NOTES:
POUR ALL EXTRA NO-Slip AND GRIP BOND DOWN DRAIN AFTER APPLICATION
	Works on Ceramic tile, quarry tile, raised safety tiles, concrete, paver block, slate, stone, chattahoochee Will not work on Vinyl tile, painted surfaces, plastic, acrylic and silicone sealers, waxed surfaces, asphalt, wood Exterior Treatment Do not apply if temperature is near or below freezing Do not apply if rain is expected during application

Contact NO-Slip before starting application (416) 256-4335

Application Directions for Non-glazed Ceramic Tiles

READ AND UNDERSTAND THESE DIRECTIONS BEFORE STARTING

1. Remove/raise all loose seating, high chairs, equipment, boxes etc. and sweep area thoroughly before starting application.
2. Pour 1 bottle Easy Green (green bottle) in mop bucket and add 3-4 gallons hot water.
3. Mop entire area with Easy Green mixture - deck brush entire area if possible.
4. Rinse floor thoroughly with clean, hot water using 2nd mop bucket.
5. Allow floor to completely dry before proceeding with application

NOTE: Only Application Crew are allowed to walk on floors after cleaning.

EMPTY AND RINSE BOTH MOP BUCKETS

* Pour entire gallon container of Grip Bond (dark purple color) into your mop bucket and add 3 gallons of hot water.

* Fill with clean, hot water.

Once these 2 buckets are ready put them aside near starting point of Step 4

BEFORE YOU START REMEMBER

• Use a new clean and dry mop head for applying NO-Slip.
• DO NOT let any water come into contact with NO-Slip it will damage treatment.
• Clean dirt and grease from the bottom of shoes and wipe dry.
• Do not walk through treated area bfore or after Step 3.

Area must be thoroughly DRY before applying NO-Slip

~ leave ventilation fans (HVAC unit) on

1. Using new, clean dry mop head, start at one end of area.
2. Pour NO-Slip (clear bottle) directly onto the mop head on the floor and slowly spread generous, thick amounts throughout floor area being treated.
3. Note the time the crew starts applying NO-Slip and count 7 minutes on your watch before proceeding to Step 5.

IMPORTANT NOTES

1. DO NOT LET NO-Slip DRY. If you see dry spots, apply more NO-Slip immediately.
2. If you splash glass or metal clean it immediately with generous amounts of water.
3. Do not leave mop soaked with clear NO-Slip sitting directly on the floor after use. Put on cardboard or plastic (after treatment you can rinse mops with water and reuse).
4. Do not walk through treated area before or after Step 3.

1. At 7 minutes (from beginning of Step 4) apply generous amounts of Grip Bond solution (from bucket pre-mixed with water) to floor area with mop (from cleaning) starting at the same endand following same path and at approximately the same speed you applied NO-Slip.
   Bubbles help you see where you have applied Grip Bond.
2. Immediately after Grip Bond has been applied, rinse the floor with hot water to remove bubbles (2nd Bucket): begin at the original point again using mops from cleaning and applying NO-Slip
3. Replace bubbly water in the bucket often with fresh, hot water.
4. Rinse floor twice.

Complete and submit Warranty Registration

---

Application Directions

Ceramic and Porcelain Bathtubs & Shower Tiles

Start with clean, dry, soap residue free surface.

1. Spread NO-Slip (clear) with a clean, dry sponge liberally across the entire surface to be treated.
   Wait 7 minutes - do not let the NO-Slip dry.
2. Spread Grip Bond (purple) mixture* liberally across entire treated surface using sponge or sponge mop.
3. Rinse thoroughly with hot water.

NOTES:
- * mix 3 parts water:1 part Grip Bond
- Use NO-Slip undiluted & only use clean, dry sponge.
- Leave ventilation fan on.
- Use non-abrasive liquid cleaner to clean tubs and tile.

Complete and submit Warranty Registration